Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the appropriate equipment and technical know-how. They will be able to create and program new keys much faster than a dealership would and at a lower cost.
If your key fob has stopped locking or unlocking your doors it could be due to a dead battery in the coin. There are peugeot 107 remote key replacement g28carkeys.co.uk that the key may be malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking and won't start the engine. In this situation you'll need make use of the alternative method for starting described in your vehicle owner's manual.
Another reason why the 208 won't start is that the spark plugs have worn down. The spark plugs light the fuel to start the engine. They are only able to last for a short time. If they're not used enough, they will eventually fail.
Luckily, there's an easy solution for this issue. Check the voltage of the battery with a multimeter. If it is below 11.5 Volts, then you need to replace it. If the battery is damaged, it is important to clean its contacts. You can do this by lifting the rubber covers that cover the two battery terminals and using a wire brush to remove any corroded components of the battery. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 won't start and the battery hasn't gone flat, you should check the spark plugs. You might find that they are simply too filthy and don't spark. The spark plugs can be cleaned in the workshop.
Peugeot automobiles use a key with a transponder that is compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.
Water damage is a typical cause of this issue. This is a common issue in warmer climates where the vehicle has been exposed to rain or snow. In this instance, you should contact a reliable locksmith who has the tools and equipment required to reprogram the key. They'll also have the latest technology and equipment required to make a Peugeot smart key. The process should not take more than 15 minutes.
Faulty Battery Contacts
Peugeot changed from the old carbon-encased transponder chips to an entirely new kind of chip that utilizes electronic components on a circuit board. The new system is excellent when it's brand new, but the circuit boards wear out over time and stop working properly.
This could stop the immobiliser from activating so your vehicle won't be able to start. If this happens it's a good idea contact a Peugeot specialist or locksmith.
A common issue is when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars will replace the battery and cut a new blade for you. This is a simple fix.
Faulty Receiver Module
If your Peugeot key fob stopped working after dropping it on the floor, or being exposed to a sudden downpour or accidently washing it or washing it, it could be due to a defective receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which controls the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals that block water from reaching the chip inside. The chip can be damaged by water if it is exposed to water for long periods of time. Submerging the key fob in ocean water on the beach or throwing it into the pool can be especially damaging because of the high salt content.
If your Peugeot spare key fob stops working You'll need the module replaced. This is only done by a Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the right programming to allow the car to start. This is why you should trust an experienced Peugeot locksmith to handle the task of creating and programming a replacement.
Faulty On-Board Computer
The on-board computer in your Peugeot is responsible for a variety of the systems inside the car, from power windows to the airbags. The on-board computer will show a code if something goes wrong. This code will be saved in the system until the issue is fixed. Usually, this will mean replacing the onboard computer.
One of the main reasons for the light coming on is loose or corroded connection in the airbag sensor. This could be due to wear and tear, aging, exposure to moisture and salt. This issue needs to be addressed as soon you can, since an airbag malfunctioning could pose a risk in the event of an accident.
If you find an error message stating that the card is not found on your Peugeot, the key battery inside the key fob could be dead or weak. This prevents the key fob from sending a signal that disables the immobilizer on your vehicle's standard. Test this by pressing the unlock button on the fob's key, then trying to start your car. If this fails then the battery in the key must be replaced.